11/24/2021

Advanced Diagnostics Port Devices Driver

Synaptics TouchPad Driver 19.2.17.59 for Windows 10 The Synaptics Gesture Suite device driver is now equipped with Scrybe Gesture Workflow Technology – the next generation in TouchPad-based PC. Diagnostic Tool is a fast and simple tool, which allows users of Control Techniques' drives to quickly solve any error codes that the drive may show. Built within the app are easy to locate wiring diagrams for first time setup and fault finding with links to the relevant comprehensive manuals. Find the option 'Port Check Test', and set it to 'Enabled'. It is usually in the top menu or in the 'SVC Menu' submenu. It is usually in the top menu or in the 'SVC Menu' submenu. (substituted with the numbers in your model's name, for example 3845#. # will be 3845#.505# for LG-D505). WMR Device Diagnostic Utility. The WMR Device Diagnostic Utility software allows you to view and change which COM port your RIGblaster is connected to. It also allows you to test a COM port to make sure that the RIGblaster is functioning correctly. This software can be used with all RIGblaster models. It can also be used to monitor and change settings in the Epic PWRgate.

Enable Qualcomm Diagnostic Mode useful for changing the IMEI or repair baseband your phone using QPST or other tools. There are three ways to activate Diag Mode.

1. Dial Number

Microsoft Driver Diagnostic

Advanced Diagnostics Port Devices DriverAdvanced

Type *#*#717717#*#* on dialpad. If this does not work, do the second way.

2. ADB

  1. Your phone must be rooted.
  2. Enable USB Debugging.
  3. Connect device to computer.
  4. Open Minimal ADB and Fastboot command prompt.
  5. Type adb devices → enter.
  6. adb shell → enter.
  7. su → enter.
  8. setprop sys.usb.config diag,adb → enter.

3. Terminal Emulator App (APK)

  1. Your phone must be rooted.
  2. Install Terminal Emulator Apk on your phone.
  3. Connect device to computer.
  4. Enable USB Debugging.
  5. Open terminal emulator.
  6. Type su → enter.
  7. setprop sys.usb.config diag,adb → enter.

If your cheap BMW INPA K+DCAN USB interface with FTDI chip failed to install drivers or the system prompt cannot locate the drivers. Here is a little write-up on how to fix it.

Disclaimer:
I am using Windows 8.1 system. No sure if it works on yours. You are on your own risk.

Pre-installation caution:
Here are the INPA driver & software, free download links. If the driver/software is working, then ignore the next part. Otherwise take a look at the following part for reference.
INPA Driver: http://www.obd2vip.com/download/inpa-driver.zip(Close antivirus software or set your browser to download success)
INPA software: http://www.obd2vip.com/download/inpa-2.zip

Advanced Diagnostics Port Devices Driver

Procedure:

1. Open your Device Manager. Control Panel–Hardware & Sound–Device Manager.
2. Connect the INPA K+DCAN cable with computer/PC-Double click
3. Locate USB Serial Converter->DetailsDropdown Menu->Hardware IDs. The PID number is the one you want. Will most likely be 0000.
4. Download CDM v2.08.30
http://www.ftdichip.com/Drivers/CDM/CDM%20v2.08.30%20for%20Windows%208.1.zip

5. Disable “Driver signature verification” Settings–Change PC Settings–Recovery–Advanced Startup–Restart.
This will restart your PC to Advanced settings. From there: Troubleshoot–Advanced Options–Startup Settings–Restart–F7

Follow these picture guides:
Your PC will then restart with signature verification disabled. You are now able to edit the INPA drivers.

6. Unzip the Drivers file that you just downloaded and open up

7. Open ftdibus.inf
8. Replace every PID_6001 with PID_0000 to match your hardware ID. Scan through the whole document. Then save it.
9. Then find ftdiport.inf. Do the same to ftdiport.inf

10. Back in your Device Manager double click on your OBDII cable again.
Locate USB Serial Convertor Properties->Driver->Update Driver-> Browse my computer.
Locate your driver and install. You will need to install it for both USB Serial Converter and Ports & COM.

11. Setup INPA cable as normal and run INPA software.

Advanced Diagnostics Port Devices Drivers

It seems that the white FTDI chip INPA cables have to be manually put into D-CAN mode. This file will take care of that. It is normal for the LED to go out.
http://www.mediafire.com/download/35fnrnd3q3dvf3w/D-CAN.exe
If you put the cable into DCAN mode, the LED goes off, and it says there is no adapter connected. Please connect it to the car and run the DCAN mode.

Advanced Diagnostics Florida

Who Viewed This Article Also Views: